Prevalencia de cristales de colesterol en granulomas perirradiculares de origen endodóntico / Prevalence of cholesterol crystals in periradicular granulomas of endodontic origin

Resumen Objetivo Comparar dos procedimientos de soldadura convencionales empleando una aleación de Cr-Co, para conectar barras coladas seccionadas a ser fijadas sobre implantes. Materiales y métodos A partir de un modelo maestro que representa un maxilar desdentado con cuatro implantes, se confeccionaron veinte (n=20) probetas seccionadas en tres partes. Se conformaron dos grupos, cada uno con diez (n=10) ejemplares. Una vez acondicionadas, fueron atornilladas al modelo maestro. Su desajuste inicial se analizó utilizando una lupa estereoscópica, con una cámara incorporada y un software. Las partes fueron soldadas empleando un procedimiento diferente para cada grupo. Las correspondientes al Grupo I se invistieron en un block refractario a base de sílico-fosfato. Las del Grupo II se montaron en una estructura metálica Clever Spider. El desajuste fue mensurado y los resultados procesados estadísticamente. El nivel de significación fue establecido en p<0,05. Resultados El Grupo I tuvo un desajuste inicial de 97,30±13,81μm y el Grupo II de 98,53±11,24μm. Luego de la soldadura, el Grupo I registró 98,53±17,17μm, 1,23μm mayor respecto al inicial. En el Grupo II se observó 103,13±17,61μm, 4,60μm por encima del original. Se analizaron mediante prueba t de Student; en ambos casos el resultado fue de p>0,05. Al comparar entre sí los grupos I y II, por medio de la prueba t y de comprobación no paramétrica de Mann-Whitney, se observaron diferencias no significativas, p=0,41 y p=0,38 respectivamente. Conclusiones Bajo las condiciones de este estudio, se observó que los dos métodos de soldadura analizados fueron confiables para unir supraestructurasos metálicas sin que se afecte su ajuste final.

Abstract Aim Compare two conventional welding procedures using a Cr-Co alloy, to connect sectioned cast bars to be fixed on implants. Materials and methods From a master model representing a toothless jaw with four implants, twenty (n=20) specimens sectioned into three parts were made. Two groups were formed, each with ten (n=10) specimens. Once conditioned, they were screwed to the master model. Its initial mismatch was analyzed using a stereoscopic magnifier, with a built-in camera and a software. The parts were welded using a different procedure for each group. Those corresponding to Group I were invested in a refractory block based on silyl-phosphate. Those of Group II were mounted on a Clever Spider metal structure. The mismatch was measured, and the results processed statistically. The level of significance was established at p<0.05. Results Group I had an initial mismatch of 97.30 ±13.81μm, and Group II of 98.53±11.24μm. After welding, Group I registered 98.53±17.17μm, 1.23μm higher than the initial one. In Group II, 103.13±17.61μm was observed, 4.60μm above the original. They were analyzed using Student's t test; in both cases the result was p>0.05. When comparing groups I and II, using the t-test and the Mann-Whitney nonparametric verification, non-significant differences were observed, p=0.41 and p=0.38 respectively. Conclusions Under the conditions of this study, it was observed that the two welding methods analyzed were reliable for joining metallic superstructures without affecting their final fit.

Estudio in vitro del ajuste de supraestructuras pasivadas sobre implantes múltiples / In vitro study of the adjustment of passivated suprastructures on multiple implants

Resumen Objetivo Comparar dos procedimientos de soldadura convencionales empleando una aleación de Cr-Co, para conectar barras coladas seccionadas a ser fijadas sobre implantes. Materiales y métodos A partir de un modelo maestro que representa un maxilar desdentado con cuatro implantes, se confeccionaron veinte (n=20) probetas seccionadas en tres partes. Se conformaron dos grupos, cada uno con diez (n=10) ejemplares. Una vez acondicionadas, fueron atornilladas al modelo maestro. Su desajuste inicial se analizó utilizando una lupa estereoscópica, con una cámara incorporada y un software. Las partes fueron soldadas empleando un procedimiento diferente para cada grupo. Las correspondientes al Grupo I se invistieron en un block refractario a base de sílico-fosfato. Las del Grupo II se montaron en una estructura metálica Clever Spider. El desajuste fue mensurado y los resultados procesados estadísticamente. El nivel de significación fue establecido en p<0,05. Resultados El Grupo I tuvo un desajuste inicial de 97,30±13,81μm y el Grupo II de 98,53±11,24μm. Luego de la soldadura, el Grupo I registró 98,53±17,17μm, 1,23μm mayor respecto al inicial. En el Grupo II se observó 103,13±17,61μm, 4,60μm por encima del original. Se analizaron mediante prueba t de Student; en ambos casos el resultado fue de p>0,05. Al comparar entre sí los grupos I y II, por medio de la prueba t y de comprobación no paramétrica de Mann-Whitney, se observaron diferencias no significativas, p=0,41 y p=0,38 respectivamente. Conclusiones Bajo las condiciones de este estudio, se observó que los dos métodos de soldadura analizados fueron confiables para unir supraestructurasos metálicas sin que se afecte su ajuste final.

Abstract Aim Compare two conventional welding procedures using a Cr-Co alloy, to connect sectioned cast bars to be fixed on implants. Materials and methods From a master model representing a toothless jaw with four implants, twenty (n=20) specimens sectioned into three parts were made. Two groups were formed, each with ten (n=10) specimens. Once conditioned, they were screwed to the master model. Its initial mismatch was analyzed using a stereoscopic magnifier, with a built-in camera and a software. The parts were welded using a different procedure for each group. Those corresponding to Group I were invested in a refractory block based on silyl-phosphate. Those of Group II were mounted on a Clever Spider metal structure. The mismatch was measured, and the results processed statistically. The level of significance was established at p<0.05. Results Group I had an initial mismatch of 97.30 ±13.81μm, and Group II of 98.53±11.24μm. After welding, Group I registered 98.53±17.17μm, 1.23μm higher than the initial one. In Group II, 103.13±17.61μm was observed, 4.60μm above the original. They were analyzed using Student's t test; in both cases the result was p>0.05. When comparing groups I and II, using the t-test and the Mann-Whitney nonparametric verification, non-significant differences were observed, p=0.41 and p=0.38 respectively. Conclusions Under the conditions of this study, it was observed that the two welding methods analyzed were reliable for joining metallic superstructures without affecting their final fit.

Exponential modelling of heart rate recovery after a maximal exercise

Objectives: Heart rate recovery (HRR) after exercise is clinically important as a predictor of mortality. In addition, HRR is an indicator of cardiac autonomic activity, since increased vagal activity and diminished sympathetic activity return the heart rate to resting conditions after exercise. The previous attempts to model HRR using polynomial, first-order and second-order modelling have produced mixed results. In this study, we hypothesised that the double-exponential fit would model the HRR more accurately than the single-exponential fit as it would capture the activity of both autonomic arms responsible for heart rate decay and investigated the outcome of these two models on the HRR data following a maximal exercise. Materials and Methods: Exponential curve fitting was done on a set of previously published data from our laboratory. The HRR data were acquired from 40 male participants (19–38 years) after a maximal treadmill exercise. The normalised HRR data from a 5-min time window from maximal heart rate were fitted using single and double-exponential curves, to obtain, respectively, the time constants Tau and, Tau 1 and Tau 2. The goodness-of-fit of the model was assessed with Chi-square values computed for each participant data set with both models. Considering that Chi-square of zero is a perfect fit, and therefore, smaller Chi-square values indicate a better fit than larger values, we computed the difference in the Chi-square values (??2 ) between the models by subtracting the Chi-square value of the double-exponential fit from the Chi-square value of the singleexponential fit. This was based on the premise that if the calculated ??2 is positive, it would indicate a better fit with double-exponential than single-exponential decay model. The data are presented as mean ± standard deviation. Comparisons were made with Student’s t-test. Results: Data from four participants were excluded for technical reasons. The Tau of the single-exponential fit was 65.50 ± 12.13 s, while Tau 1 and Tau 2 of the double-exponential fit were 43.75 ± 18.96 s and 120.30 ± 91.32 s, respectively, the Tau 1 value being significantly lower than the Tau 2 value (P < 0.0001). Remarkably among the 36 participants, the difference in the Chi-square value was positive (127.2 ± 171.04) in 22 subjects and zero or marginally negative (?0.17 ± 0.31) in 14 subjects. Conclusion: Our results indicate that the double-exponential model fitted the HRR data better than the single-exponential model in almost two-thirds (61%) of our study population. In the remaining participants, the goodness-of-fit was nearly equivalent for both fits with no evidence of superior modelling with the singleexponential fit. Our data show that while the single-exponential fit is sufficient for modelling the HRR of 14 subjects, it was less efficient for fitting the data of most participants. In comparison, the double-exponential curve fit effectively modelled 100% of our study population. Given our findings, we conclude that the doubleexponential model is more inclusive and better represented the HRR data of our study population than the singleexponential model.

The chain mediating effect of professional identity and person-organization fit on the relationship between spiritual leadership and work engagement of young nurses / 中国实用护理杂志

Objective:To explore the relationship between spiritual leadership, professional identity, person-organization fit and work engagement of young nurses, so as to provide reference for developing strategies to improve young nurses′ work engagement.Methods:This was a cross-sectional study. From December 2021 to April 2022, 449 young nurses from 9 hospitals in Shandong province were investigated by general data questionnaire, Spiritual Leadership Scale, Professional Identity Rating Scale, Nurse Person-organizational Fit Assessment Scale and Work Engagement Scale.Results:The scores of professional identity, spiritual leadership, person-organization fit and work engagement of young nurses were (116.04 ± 23.06), (68.07 ± 13.87), (163.50 ± 25.88), (38.80 ± 14.65) points, respectively. The total effect of spiritual leadership on work engagement was 0.707. The mediating path of spiritual leadership to work engagement included spiritual leadership→professional identity→work engagement; Spiritual leadership→person-organization fit→work engagement. Spiritual leadership→professional identity→ person-organization fit→work engagement. Three indirect effects accounted for 63.60%, 6.80% and 10.60% of the total effect, respectively.Conclusions:Professional identity and person-organization fit play chain mediating effect between spiritual leadership and work engagement of young nurses. Nursing managers should implement spiritual leadership to improve young nurses′ professional identity and person-organization fit, and then improve the level of young nurses′ work engagement.

Analysis of verification results of protective effects of hearing protectors in different industries / 中华劳动卫生职业病杂志

Objective: To get insight into the current practice of noise reduction effect of workers as they wore hearing protectors in different domestic enterprises and the possible affected factors. Methods: From October 2020 to April 2021, using a random sampling method, 1197 workers exposed to noise in petrochemical factories, textile factories, and parts manufacturing factories were selected as the study subjects. The noise reduction effect of hearing protectors worn by workers in daily use was tested using a hearing protector suitability testing system. The personal sound attenuation level (PAR) was compared among workers in three enterprises, Targeted intervention and repetitive testing were conducted for workers who did not meet the noise reduction effect required by the enterprise, and the changes in PAR of workers before and after the intervention were compared. The comparison of baseline PARs between two or more groups was performed using the Mann Whitney test, the comparison of baseline PARs with post intervention PARs was performed using the Wilcoxon signed rank sum test, and the comparison of qualitative data between two or more groups was performed using the Chi square test. Results: The median baseline PAR for all workers was 15 dB. Men, age<30 years old, education level at or above college level, working experience of 5 to 15 years, and those who used hearing protectors for 5 to 15 years had higher PARs, with statistically significant differences (P<0.05). The median difference in baseline PAR among workers from three enterprises was statistically significant (H=175.06, P<0.01). The median PAR of subjects who did not pass the baseline increased from 3 dB to 21 dB after intervention (Z=-27.92, P<0.01) . Conclusion: Some workers wearing hearing protectors do not meet the required PAR, and low PARs may be related to incorrect wearing methods and incorrect selection of hearing protectors. As a tool for testing, training, and assisting in selection, the hearing protector suitability testing system is of great significance for worker hearing protection.

Microleakage of chairside moulded, 3D-printed and milled provisional restorations using a curve-fit approach

Abstract The purpose of this study was to evaluate and measure the microleakage inhibiting quality of provisional restorations manufactured using computer-aided manufacturing, 3D printing, and chairside molded provisional restorative materials. Fifteen provisional restorations each from 3D printed, milled, and chairside molded were manufactured. All restorations were cemented onto sintered zirconia abutment dies and adhered with zinc-oxide non-eugenol temporary cement. Artificial aging was conducted by thermocycling for 800 cycles to simulate 1 month of clinical use. All specimens were submerged in 2% (w/w) methylene blue for 24 hours at 37°C, sectioned, and analyzed digitally for the distance of dye penetration through image analysis. The data were analyzed using the Kruskal-Wallis test with Dunn-Bonferroni post-hoc. Significant differences in dye penetration depth were observed between all groups except milled vs chairside molded. Light microscopy revealed differences in mean cement thickness for 3D printed, milled, and chairside molded of 83.6 µm (1σ = 31.9 µm), 149.1 µm (1σ = 88.7 µm) and 137.9 µm (1σ = 67.2 µm) respectively. Conclusion: 3D printed provisional restorations were found to have the least amount of microleakage compared to milled and chairside molded provisional restorations.

Resumo O objetivo deste estudo foi avaliar e medir a qualidade de inibição de microinfiltração de restaurações provisórias fabricadas usando manufatura assistida por computador, impressão 3D e materiais de restauração provisória moldados no consultório. Foram fabricadas 15 restaurações provisórias impressas em 3D, fresadas e moldadas em consultório. Todas as restaurações foram cimentadas em matrizes de pilar de zircônia sinterizada e aderidas com cimento temporário de óxido de zinco sem eugenol. O envelhecimento artificial foi conduzido por termociclagem por 800 ciclos para simular 1 mês de uso clínico. Todos os espécimes foram submersos em azul de metileno a 2% (p/p) por 24 horas a 37°C, seccionados e analisados digitalmente quanto à distância de penetração do corante por meio de análise de imagem. Os dados foram analisados usando o teste de Kruskal-Wallis com post-hoc de Dunn-Bonferroni. Foram observadas diferenças significativas na profundidade de penetração do corante entre todos os grupos, exceto entre fresado e moldado na cadeira. A microscopia óptica revelou diferenças na espessura média do cimento para as restaurações impressas em 3D, fresadas e moldadas em cadeira de 83,6 µm (1σ = 31,9 µm), 149,1 µm (1σ = 88,7 µm) e 137,9 µm (1σ = 67,2 µm), respectivamente. Conclusão: As restaurações provisórias impressas em 3D apresentaram a menor quantidade de microinfiltração em comparação com as restaurações provisórias fresadas e moldadas no consultório.

Evaluation of customized peripheral sealing device acceptance for surgical/medical masks among dental professionals during early COVID-19 pandemic / Evaluación de la aceptación de dispositivos de sellado periférico personalizados para máscaras quirúrgicas/médicas entre dentistas durante la pandemia temprana de COVID-19

Abstract A 3-dimensional (3D) printed custom-frame can improve the peripheral seal of readily available surgical/medical masks. This study aimed to assess the acceptance of a 3D-printed custom-frame with the American Society for Testing and Materials (ASTM) surgical/medical masks and the use of a face shield. A total of 206 subjects from a dental school participated, who answered a multiple-choice questionnaire. Participants received an invitation through the institutional email of the school via Qualtrics platform. 3D printed custom-frames were fabricated for each participant. According to their response, participants were divided into 4 groups: mask only (M), mask and frame (MF), mask and face shield (MFS), and all 3 personal protective equipment (MFFS). Data was analyzed in absolute and relative frequency. The acceptance of a 3D-printed custom-frame in the group MFFS varied between ''poor''/''very poor'' (44.7%). It allowed ''good'' performance of routine procedures (40.3%), but ''poor'' visual quality (48.1%). Musculoskeletal tolerance and ease to perform movements were adequate. There was no interference in olfactory sensitivity (44.7%) or in the ability to breathe (34.5%). Finally, it showed "moderate pain" (48.1%) on the ear and "no pain" (38.9%) on the head. The 3D-printed custom-frame adapted to ASTM surgical/medical face masks showed reasonable tolerance. Side effects of ear pain ranging in degrees were noted. Further research is indicated to evaluate safety, comfort, compliance, side effects, and occupational hazards of long-term use of enhanced PPE recommendations.Avoiding the recurrent outbreaks of COVID-19, the use of PPE by the public is necessary. Improper PPE use is a major source of concern for human and environmental health. Preventing such activities can be done by following steps involved in PPE disposals or by getting a new way to re-use such as improving peripherical sealing. Our work highlights that a custom-frame can improve protection, without adverse effects.

Resumen El sellado periférico de las máscaras médicas/quirúrgicas puede ser mejorado fácilmente mediante un marco personalizado impreso en 3 dimensiones (3D). Este estudio tuvo como objetivo evaluar la aceptación de un marco personalizado impreso en 3D cuando usado en combinacion con máscaras médicas/quirúrgicas de la Sociedad Estadounidense para Pruebas y Materiales (ASTM) asi como con el uso de protector facial. Participaron un total de 206 sujetos de una facultad de odontología, quienes respondieron un cuestionario de opción múltiple. Los participantes recibieron una invitación a través del correo institucional de la escuela a través de la plataforma Qualtrics. Se fabricaron marcos personalizados impresos en 3D para cada participante. Según su respuesta, los participantes se dividieron en 4 grupos: solo máscara (M), máscara y marco (MF), máscara y protector facial (MFS) y los 3 equipos de protección personal (MFFS). Los datos se analizaron en frecuencia absoluta y relativa. La aceptación de un marco personalizado impreso en 3D en el grupo MFFS varió entre ''pobre''/''muy pobre'' (44,7%). Permitió un ''buen'' desempeño de los procedimientos de rutina (40,3%), pero una ''mala'' calidad visual (48,1%). La tolerancia musculoesquelética y la facilidad para realizar movimientos fueron adecuadas. No hubo interferencia en la sensibilidad olfativa (44,7%) ni en la capacidad de respirar (34,5%). Finalmente, mostró "dolor moderado" (48,1%) en el oído y "sin dolor" (38,9%) en la cabeza. El marco personalizado impreso en 3D adaptado a las máscaras faciales quirúrgicas/ médicas de ASTM mostró una tolerancia razonable. Se observaron efectos secundarios de dolor de oído que variaron en grados. Estudios futuros deben evaluar la seguridad, la comodidad, efectos secundarios y los riesgos laborales del uso a largo plazo para este tipo de combinación. Para evitar los brotes recurrentes de COVID-19, es necesario el uso de equipamento personal de protección (EPP) por parte del público. El uso inadecuado de EPP es una fuente importante de preocupación para la salud humana y ambiental. La prevención de tales actividades se puede hacer siguiendo los pasos involucrados en la eliminación de EPP o obteniendo una nueva forma de reutilización, como mejorar el sellado periférico. Nuestro trabajo resalta que un marco personalizado puede mejorar la proteccion, sin afectos adversos.

Mexican Validation of the MOS Questionnaire on Perceived Social Support in the Context of the COVID-19 Pandemic

Introduction: The COVID-19 pandemic has had a very negative impact on people's overall mental health and psychosocial well-being, but the study of available social support to cope with such an adverse situation has received hardly any attention. Objective: To examine the psychometric properties of the MOS Perceived Social Support Questionnaire among the Mexican population in the context of the COVID-19 pandemic. Method: Non-experimental cross-sectional study. A sociodemographic questionnaire and the Medical Outcomes Study were applied in a non-probabilistic sample. A total of 898 people from different regions in Mexico, 258 males and 640 females, participated in the study in the context of the COVID-19 pandemic. Results: The analysis yielded a bi-factor model with two factors, Emotional/informational support and Tangible support, with satisfactory goodness of fit indices. Reliability was adequate with a high hierarchical omega coefficient, as well as in the factors. Likewise, the H coefficient was adequate in the general factor and its dimensions. Conclusions: Results showed that the scale is a valid and reliable measure of perceived social support among the Mexican population.

Introducción: La pandemia de COVID-19 ha tenido un impacto muy negativo en la salud mental y el bienestar psicosocial general de las personas, pero el estudio del apoyo social disponible para hacer frente a una situación tan adversa como esta ha recibido muy poca atención. Objetivo: Examinar las propiedades psicométricas del Cuestionario MOS de Apoyo Social Percibido en población mexicana en contexto de pandemia por COVID-19. Método: Diseño no experimental transversal. Se aplicó un cuestionario sociodemográfico y el Medical Outcomes Study en una muestra no probabilística por conveniencia. Participaron 898 personas de diferentes regiones de México, 258 hombres y 640 mujeres, durante el contexto de la pandemia por COVID-19. Resultados: El análisis arrojó un modelo Bi-factor de dos factores Apoyo emocional/ informacional y Apoyo tangible, con índices de bondad que se ajustaron a los datos. La fiabilidad fue adecuada con un coeficiente de omega jerárquico alto, así como en los factores. Asimismo, el coeficiente H fue adecuado en el factor general y sus dimensiones. Conclusiones: La escala presenta validez y confiabilidad para medir el apoyo social percibido en población mexicana.

Three-dimensional assessment of internal adaptation measurement of three cad/cam ceramic systems

Abstract This study aimed to evaluate the internal adaptation of three different computer-aided design/computer-aided manufacturing (CAD/CAM) ceramic crowns. The internal adaptation of a polymer-infiltrated ceramic network material (Vita Enamic [VE]) was compared to two machinable glass-ceramics; Zirconia-reinforced lithium silicate (Vita Suprinity [VS]) and a lithium disilicate glass-ceramic (IPS e.max. CAD). Thirty human premolars of average size were prepared (n=10 each group) by computer numerical control to fulfill the criteria of all-ceramic crown design. Optical impressions were taken for each tooth preparation using the CAD/CAM scanner. Thirty crowns were fabricated using CAD/CAM system and divided into three groups (IPS e.max, VE, and VS). To assess the internal fit of tested crowns, the gap between the intaglio of each crown and the corresponding tooth surface was evaluated using a 3D digital scanner using the Triple-scan Protocol. One-way ANOVA followed by Tukey Post Hoc statistical tests were used to statistically analyze results of the internal fit. There was a statistically significant difference for all groups at the four axial walls (p = 0.000002). For total internal fit between groups, comparisons showed a statistically significant difference between all tested groups (p=0.000002). When each pair of groups was statistically compared with each other, all pair comparisons showed a statistically significant difference. IPS e.max CAD had the best internal fit, followed by Vita Enamic, then Vita Suprinity. For all ceramics tested, values of internal fit of all ceramics tested were within the clinically acceptable range.

Resumo Este estudo teve como objetivo avaliar a adaptação interna de três diferentes coroas cerâmicas CAD/CAM (Computer-aided design/computer-aided manufacturing). A adaptação interna de um material cerâmico de rede com infiltração de polímero (Vita Enamic [VE]) foi comparada com duas cerâmicas de vidro maquináveis; silicato de lítio reforçado com zircónio (Vita Suprinity [VS]) e uma cerâmica-vidro de dissilicato de lítio (IPS e.max. CAD). Trinta dentes pré-molares humanos de tamanho médio foram preparados (n=10 cada grupo) por controle numérico computadorizado para preencher os critérios de desenho de coroa em cerâmica pura. Foram tiradas impressões ópticas para cada preparação dentária utilizando o scanner CAD/CAM. Trinta coroas foram fabricadas usando o sistema CAD/CAM e divididas em três grupos (IPS e.max, VE, e VS). Para avaliar o ajuste interno das coroas testadas, o espaço entre o entalhe de cada coroa e a superfície dentária correspondente foi avaliado usando um scanner digital 3D usando o Protocolo Triple-scan. Para analisar estatisticamente os resultados do ajuste interno, utilizou-se a ANOVA unidirecional seguida dos testes estatísticos Tukey Post Hoc. Houve uma diferença estatisticamente significativa para todos os grupos nas quatro paredes axiais (p = 0,000002). Para o ajuste interno total entre grupos, as comparações mostraram uma diferença estatisticamente significativa entre todos os grupos testados (p=0,000002). Quando cada par de grupos foi comparado estatisticamente uns com os outros, todas as comparações de pares mostraram uma diferença estatisticamente significativa. IPS e.max CAD teve o melhor ajuste interno, seguido por Vita Enamic, depois Vita Suprinity. Para todas as cerâmicas testadas, os valores de ajuste interno de todas as cerâmicas testadas encontravam-se dentro da gama clinicamente aceitável.

Análisis factorial confirmatorio de la Escala verbal de fusión de identidad en una muestra chilena / Confirmatory factor analysis of the Verbal Identity Fusion Scale in a Chilean sample

Resumen La fusión de identidad consiste en un sentimiento de unión con un grupo, en el que el individuo experimenta una mezcla entre su identidad personal y la social; y es un buen predictor de la conducta extrema progrupo. El presente estudio analizó la estructura factorial de la Escala verbal de fusión de identidad elaborada por Gómez et al. (2011), en una muestra chilena. Se utilizó una muestra universitaria seleccionada por conveniencia de 411 participantes (66% mujeres) con una edad media de 24.45 años (DT = 5.89). Se analizó el ajuste unifactorial y bifactorial de la Escala a través del análisis factorial, y las respectivas confiabilidades. Los resultados indicaron un buen y mejor ajuste del modelo bifactorial (χ 2/gl = 3.34, p < .001, CFI = .975, TLI = .957, SRMR = .030, y RMSEA = .085), por sobre el unifactorial, que no mostró un buen ajuste (χ 2/gl = 5.26, p < .001, CFI = .946, TLI = .919, SRMR = .042, y RMSEA = .116). Ambos modelos contaron con altas confiabilidades (> .800). Se discutió sobre el mejor ajuste de la estructura bifactorial en relación con estudios realizados en Estados Unidos, España y población inmigrante en Chile. Se proyecta la necesidad de futuros estudios que incorporen otros análisis de validez y superen la limitación del presente estudio asociada al uso de una muestra no representativa.

Abstract Identity fusion consists in a form alignment with a group and is a significant predictor of extreme pro-group behavior. The present study analyzed the factor structure of the verbal scale of identity fusion developed by Gómez et al. (2011), in a Chilean sample. A Chilean university sample by convenience of 411 participants (66% women) with a mean age of 24.45 years (SD = 5.89) was used. One-factor and two-factor fit of the scale was analyzed through factor analysis, and the respective reliabilities. The results indicated a good and better fit of the two-factor (χ2/gl = 3.34, p < .001, CFI = .975, TLI = .957, SRMR = .030, and RMSEA = .085), than the one-factor model, which did not show a good fit (χ2/gl = 5.26, p < .001, CFI = .946, TLI = .919, SRMR = .042, and RMSEA = .116). Both models had high reliabilities (> .800). The better fit of the two-factor structure was discussed in relation to studies conducted in the United States, Spain, and an immigrant population in Chile. The need for future studies incorporating other validity analyses and overcoming the limitation of the present study associated with the use of a non-representative sample is projected.

Assessing the efficacy of 3D-printed ear protectors on mask adherence at an academic ophthalmology center

Purpose: In the ophthalmology setting, given the close proximity required for the clinical exam, appropriate mask usage and fit is essential. This study aims to assess how a simple, cost?effective 3D?printed face mask ear protectors (EP) attachment may decrease discomfort, increase compliance, and improve fit in an academic institution’s Ophthalmology department. Methods: Face mask EPs were distributed to patients and providers in the Ophthalmology department. A validated questionnaire was administered before and 2 weeks after EP usage. The survey included questions on demographics and frequency of mask usage during a spectrum of activities. Descriptive statistics were performed with Fischer’s t test. Results: Post-EP responses demonstrated an increased likelihood of mask usage across all activities, although not statistically significant. The greatest change was during outdoor activities, with a 14.3% increase in highest utilization. Post?EP, all subjects were very likely to wear masks while shopping and 91.7% while in the workplace. EP usage decreased the number of noncompliant individuals while spending time with friends and family by 93.3%. Almost no subjects reported mask removal of >15 times per hour post?EP. The increase in mask compliance was greatest for low mask utilizers. 91.9% reported improved comfort, 91.9% reported improved fit, and 81.6% reported increased mask usage. Conclusion: Our results suggest that simple cost?effective 3D?printed ear protectors may improve fit, comfort, and overall mask compliance. The results of this study should drive broader public health efforts to further investigate whether mask attachments can improve overall mask compliance through better comfort and fit

Comparison of performance with hearing aid programmed to NAL-NL1 first-fit and optimized-fit

ABSTRACT Purpose The initial-fit provided by the hearing aid manufacturer's software is generally a display of measurement done in the ear simulators. The need for verification of hearing aid output and gain in the real ear using probe-microphone measurement to match the prescriptive target is highlighted. The objective of the study was to evaluate the difference in real-ear aided response (REAR), real-ear insertion gain (REIG), aided thresholds, articulation index (AI) and word recognition score (WRS) in quiet, with hearing aid programmed to NAL-NL1 first-fit and NAL-NL1 optimized-fit using the probe-microphone technique. Methods In a repeated measure experimental design, 11 participants with a mean age of 41.09 (SD=±9.95) years having moderate and moderately-severe sensorineural hearing loss were tested monaurally in two aided conditions, with a 16-channel hearing aid programmed for manufacturer's NAL-NL1 first-fit and optimized-fit to NAL-NL1 using probe-microphone verification. The REAR, REIG, aided threshold, articulation index and word recognition scores in quiet were obtained for both aided conditions. Results The REAR, REIG, aided threshold, AI and WRS in quiet were significantly better with the NAL-NL1 optimized-fit compared to manufacturer's NAL-NL1 first-fit. Conclusion The optimized-fit yields better audibility and improved word recognition in quiet. This supports best practice guidelines of many professional organizations regarding the use of probe-microphone measurement as the "Gold standard" for verification of hearing aid fitting, thereby providing better satisfaction and quality of life to hearing aid users.

Evaluation of methods for fitness of removable partial denture / 北京大学学报(医学版)

OBJECTIVE@#To compare the differences and indications of three evaluation methods for fitness evaluation of removable partial denture (RPD).@*METHODS@#A RPD was fabricated and seated on the stone cast of a partially edentulous mandible, and the spaces between RPD and stone cast were recorded with polyvinyl siloxane (PVS) impression material forming PVS replicas. Using cross sectional measurement, the average thicknesses of PVS replicas were measured under stereomicroscope with different numbers of selected measuring points in the denture base, major connector, occlusal rest of the RPD, and the average thicknesses of the PVS replicas measured with different numbers of measuring points were compared using one-way analysis of variance (ANOVA) and independent sample t test. Three kinds of method, including cross sectional measurement, three-dimensional analysis on the stone cast, and three-dimensional analysis on the polyether cast, were applied to measure the average thicknesses of the PVS replicas, and the average thicknesses of the PVS replicas measured by these three evaluation methods were compared with ANOVA.@*RESULTS@#For cross sectional measurement, statistically significant differences were found in the average thicknesses of the PVS replicas in the denture base and the major connector among the different numbers of measuring points (P < 0.05), but no differences were found in the average thicknesses of the PVS replicas in the occlusal rest (P>0.05). There were significant differences among the average thicknesses of the PVS replicas measured by these three evaluation methods in each component of the RPD (P < 0.01). The average thickness measured by three-dimensional analysis on the stone cast and three-dimensional analysis on polyether cast were smaller than that measured by cross sectional measurement (P < 0.05). And there were no differences between the average thicknesses of PVS replicas measured by three-dimensional analysis on stone cast and three-dimensional analysis on polyether cast (P>0.05).@*CONCLUSION@#For cross sectional measurement, the average thickness of the PVS replicas was influenced by the number of measuring points, and the measurement accuracy of cross sectional measurement was not reliable enough. Three-dimensional analysis on stone cast which is suitable for evaluation in vitro and three-dimensional analysis on polyether cast which is suitable for evaluation in vivo can evaluate the fitness of RPD more comprehensively and effectively than that of cross sectional measurement.

How to use χ2 test correctly——χ2 distribution and the related contents / 四川精神卫生

The purpose of this article was to introduce the χ2 distribution and related contents， including χ2 distribution and non-central χ2 distribution. It focused on showing the definition of two χ2 distributions， the graph and the main properties of the probability density function. Among them， the two most important properties were： first， the limiting distribution of the χ2 distribution was the normal distribution； second， n-1s2σ2followed the χ2 distribution with n-1 degrees of freedom.In addition， it also explained the relationship between the χ2 distribution and the normal distribution， the relationship between χ2 test statistic and Z test statistic. Finally， it illustrated the computational approaches of the χ2 distribution based on the two SAS functions in SAS software.

How to use χ2 test correctly—— the goodness of fit tests and the implementation of the SAS software / 四川精神卫生

The purpose of this article was to introduce the goodness of fit test and its SAS implementation. The main contents included the following four aspects： ① Pearson΄s goodness of fit test； ② deviance or likelihood ratio goodness of fit test； ③ Hosmer-Lemeshow goodness of fit test； ④ goodness of fit test for the sparse data. In the aforementioned “fourth aspect”， there were six specific test approaches， namely “information matrix test” “information matrix diagonal test” “Osius-Rojek test” “unweighted residual sum of squares test” “Spiegelhalter test” and “Stukel test”. The paper implemented the four types of the goodness of fit tests mentioned above with the help of the SAS software through an example， explained the output results， and made statistical and professional conclusions.

Valor de corte de los índices de ajuste en el análisis factorial confirmatorio

Resumen En las investigaciones psicológicas resulta de amplia relevancia conocer si los cuestionarios utilizados miden los constructos latentes de interés. A tal efecto, el Análisis Factorial Confirmatorio se emplea frecuentemente en la literatura especializada para aportar evidencias de validez a las escalas empleadas. Sin embargo, en la actualidad existe cierta disparidad de criterios respecto de los puntos de corte que deben tenerse en consideración. Por este motivo, el presente trabajo se propone revisar la literatura en torno a los diferentes puntos de corte tradicionales de los índices de ajuste más utilizados. Se concluye que para seleccionar los indices e interpretar los resultados se debe tener en cuenta que estos puntos de corte pueden cambiar por diferentes motivos, tales como el tamaño de la muestra.

Abstract In psychological research, it is of great relevance to know whether the questionnaires used measure the latent constructs of interest. For this purpose, Confirmatory Factor Analysis is frequently used in the specialized literature to provide evidence of validity to the scales used. However, there is currently a certain disparity in the criteria regarding the cut-off points to be taken into consideration. For this reason, this paper aims to review the literature on the different cut-off points for the most commonly used fit indexes. It is concluded that to select the indexes and interpret the results, it should be should take into account that these cut-off points may change for different reasons, such as sample size.

Comparison between Thin-Layer Models and Non-Traditional Methods in the Modelling of Drying Kinetics of Crustacean Wastes

Abstract This research aims to compare the classical thin-layer models, stepwise fit regression method (SRG) and artificial neural networks (ANN) in the modelling of drying kinetics of shrimp shell and crab exoskeleton. Thus, drying curves were obtained using a convective dryer (3.0 m/s) at temperatures of 30.45 and 60oC. The results showed a decreasing tendency for the drying time as the temperature increased for both materials. Drying curves modelling of both materials showed fitted results with R 2 adj >0.998 and MRE<13.128% for some thin-layer models. On the other hand, by SRG a simple model could be obtained as a function of time and temperature, with the greatest accuracy being found in the modelling of experimental data of crab exoskeleton, with MRE<10.149%. Finally, the ANNs were employed successfully in the modelling of drying kinetics, showing high prediction quality with the trained recurrent ANN models.

Cocaine Cravings, Borderline Personality Disorder & Attempted Homicide

@#In the 80’s, in Spain, there was a very significant increase in the population addicted to heroin use. The behaviour patterns of use and abuse of this substance also caused many drug addicts to be linked to the associated consumption of multiple toxic substances, favouring the appearance of politoxicomania. The origin of the change of model in drug use began in mid- 1987 and in the following years, ecstasy and the so-called designer drugs began to spread throughout the festival scene in the United Kingdom, Western Europe and the Iberian Peninsul. In the 90’s, new substances were introduced into society that had little to do with heroin use, shifting the link to toxic substances to these better accepted and less questioned substances, avoiding the possible problems associated with consumption in marginal environments. The normalization of the consumption of substances of abuse began to have a greater social tolerance, breaking the stigma that led to the alarm raised by heroin consumption in the 80’s. In this sense, drugs were no longer associated with marginalization, and were seen in environments considered festive and, therefore, “normal”. ASEAN Journal of Psychiatry, Vol. 22(5): July 2021: 1-4.

Alcohol Consumption And Intensification Of Paranoid Traits In Attempted Homicide

@#There is strong evidence that paranoia can be an existing trait in the general population as a continuous dimension ranging from minimal levels to paranoid personality traits, and that at its maximum expression could take the form of disabling psychotic disorders such as delusional disorder or schizophrenia however, and according to Caviedes, GEC and Yonfá, EDA. Here are studies in which the existence of comorbidity between paranoid, borderline, antisocial and histrionic personality and problematic alcohol consumption is mentioned which in psychopathological terminology is called dual pathology (comorbidity of mental disorder and toxic consumption).

Internal and marginal fit and fracture strength of narrow diameter dental implant-abutment assembly

Abstract The aim of this study was to assess the internal and vertical marginal fit of metallic copings to abutments and the fracture strength of different narrow diameter dental implant/abutments, either submitted to thermomechanical cycling or not. Sixty-four implant/abutments (n=16) were divided into 4 groups according to diameter and abutment type: G3.5-UAC (morse taper implant Ø3.5mm + universal abutment with beveled chamfer finish); G2.9-UAS (morse taper implant Ø2.9mm + universal abutment with shoulder finish); G2.8-AA (morse taper friction implant Ø2.8mm + anatomical abutment) and G2.5-HP (one-piece implant Ø2.5mm with indexed hexagonal platform). Each group was divided into two subgroups (n=8): submitted and not submitted to thermomechanical cycling (TMC). To assess internal and vertical marginal fit of metallic copings, the assemblies were scanned using microtomography (micro-CT) (n=5). The samples were subjected to the compressive strength test on a universal test machine. Group G3.5-UAC showed the highest marginal misfit regardless of TMC (p<0.05). All other groups were similar after TMC. Group G2.8-AA showed the lowest internal misfit both with and without TMC (p<0.05). Group G2.8-AA showed the highest fracture strength, similar only to G2.5-HP without TMC and G3.5-UAC with TMC. The type of abutment affects the internal and marginal fit of metallic copings and the anatomical abutment led to the best internal and marginal coping fit. The narrow diameter dental implant/abutments differ in terms of fracture strength, the strongest assembly was that composed by implant of type V grade titanium without internal threads (friction implant).

Resumo O objetivo deste estudo foi avaliar a adaptação marginal e interna de cópings metálicos em pilares sobre implantes, e a resistência a fratura de diferentes conjuntos de implantes/pilares de diâmetro reduzido, submetidos à ciclagem termomecânica ou não. Sessenta e quatro implantes/pilares (n=16) foram divididos em 04 grupos de acordo com o tipo de pilar e diâmetro do implante: G3.5-UAC (implante cone morse Ø3.5mm + munhão universal com término em chanfro); G2.9-UAS (implante cone morse Ø2.9mm + munhão universal com término em ombro); G2.8-AA (implante cone morse friccional Ø2.8mm + munhão anatômico); e G2.5-HP (implante de corpo único de Ø2.5mm com plataforma hexagonal indexada). Cada grupo foi dividio em dois subgrupos (n=8): submetidos ou não à ciclagem termomecânica (TMC). As amostras foram escaneadas por microtomografia (micro-CT) para avaliar a adaptação interna e marginal vertical dos copings metálicos. As amostras foram submetidas à resistência à compressão em uma maquina de ensaios universal. O grupo G3.5-UAC apresentou os maiores valores de desadaptação marginal independentemente da TMC (p<0,05). Todos os outros grupos foram similares entre si após TMC. O grupo G2.8-AA demonstrou o menor desajuste interno independentemente de TMC (p<0,05). O grupo G2.8-AA demonstrou a maior resistência à fratura, similar apenas ao grupo G2.5-HP sem TMC e G3.5-UAC com TMC. O tipo de pilar influencia a adaptação interna e marginal vertical de copings metálicos. O grupo do pilar anatômico (sem entalhes na superfície) levou à melhor adaptação, enquanto o grupo com plataforma expandida hexagonal e os grupos com munhão universal (com entalhes na superfície) proporcionaram os maiores desajustes (especialmente com termino em chanfro). Os implantes/pilares de diâmetro reduzido diferem em termos de resistencia à fratura, sendo que o conjunto mais resistente foi aquele composto por titânio tipo V e sem roscas internas (implante friccional).